Sand Length in Feet x Width in feet x depth in feet (inches divide by 12 to convert to feet) then divide by 27 to get cubic yardage. Approximate compaction factor 25% - multiply by 1.25 to get total yardage. 80' x 24' x 8 inches deep of fill sand ((80 x 24 x .667) / 27 ) x 1.25 = 59.26 yards
Concrete Ingredients Calculation. For Cement, Sand and Coarse Aggregate. This is a Volumetric Calculation. Assuming we need 2 m 3 of concrete for M20 Concrete Mix, (Mix Ratio, M20 = 1 : 1.5 : 3) Total Part of the Concrete = 1+1.5+3 = 5.5 Parts. Therefore, Cement Quantity = (Cement Part / Concrete Parts ) * Concrete Volume
Calculate Volume of Square Slab Calculator Use. Calculate volumes for concrete slabs, walls, footers, columns, steps, curbs and gutters. Enter dimensions in US units (inches or feet) or metric units (centimeters or meters) of your concrete structure to get the cubic yards value of the amount of concrete you will need to make this structure.
Type in inches and feet of your project and calculate the estimated amount of Recycled Materials in cubic yards, cubic feet and Tons, that your need for your project. The Density of 2" Minus Road base (RCA): 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t
Concrete calculator mix-on-site . This calculator estimates the required amount of cement, sand and aggregate (stone) for mixing on site for a given area of concrete. Please note that this is based on a 1:2:4 ratio mix. (Volumetric) Length (m) Depth (mm) Please note: depth is measured in mm, ...
For 1.5 inch washed landscaping rock, use the following: 1 square foot of cover = 20lbs. of rock OR 1 ton of rock will cover 100 square feet. The most common materials, like driveway gravel and basecourse, figure out to 1.5 tons per cubic yard. Materials like washed sand …
A concrete mixture ratio of 1 part cement, 3 parts sand, and 3 parts aggregate will produce a concrete mix of approximately 3000 psi.. Mixing water with the cement, sand, and stone will form a paste that will bind the materials together until the mix hardens.
Estimating concrete steps. Steps seem tricky to calculate but are not. If there are three steps leading up to a porch: Use the slab calculator to figure the concrete needed for the porch surface. Use the footing calculator to calculate the sides of the porch and the steps; Here is an example:
Step One: Calculate Volume in Yards. The first step to estimating gravel, sand, or soil is to estimate the volume of material needed. Start by measuring the length, width, and depth of the area you need to fill in the same unit of measurement.
Our sand calculator is a tool designed specifically to help you with calculations you may do on the building site, or when you are doing a bit of home improvement. Estimating the required amount of any building material is a difficult task, and errors may result in either the material running out when the project is in full swing, or in heaps ...
NOTE: This Calculator should be used as an estimating tool ONLY. Chaney Enterprises is not responsible for any discrepancies in material based on calculations made with this application. To order Sand, Gravel and Stone, call 301-932-5000 and press option 2.
Concrete Sand from Southern Crushed Concrete is a fine aggregate that is used in the production of concrete or mortar. Concrete sand is crushed in a quarry then filtered to ensure no large rock fragments are left behind. When mixed with cement and water, a grout is formed that fills the voids between the coarse aggregate.
The best way to calculate how much concrete you're going to need in cubic yards is to do the following: Mark the area that will need concrete and divide it into smaller areas. Calculate the volume of the area after determining the shape of the area (see the chart below) by multiplying in the thickness of the concrete.
This free concrete calculator estimates the amount of concrete necessary for a project, and can account for different shapes and amounts of concrete. Explore other calculators related to housing or building, as well as hundreds of other calculators addressing finance, math, fitness, health, and more.
Portland cement or fraction of bag. Example: One and half bag, Enter 1.5 Round off answer to next even higher figures. This calculator is intended for approximate guidance. Working with Concrete Tips Hand Mixing Only use clean water, sand and gravel. Aim for a mix of 1 part cement, 2-1/4 part sand and 3 parts aggregate. Mix the dry cement and sand,
These calculators are designed to help calculate the amount of concrete, asphalt, or sand and gravel needed for your project. The following conditions may affect the actual quantity needed: Any variations in the subgrade, even a quarter inch variation can make a substantial difference in the quantity.
Example calculation Estimate the quantity of cement, sand and stone aggregate required for 1 cubic meter of 1:2:4 concrete mix. Ans. Materials required are 7 nos. of 50 kg bag of cement, 0.42 m 3 of sand and 0.83 m 3 of stone aggregate.
Concrete Block Calculator & Estimator. Use the block calculators below to calculate the amount of materials needed. Block required. Length (ft): Height (ft): Total Block Required: (add approx. 5% to the total for waste) Sand amount needed for block count. Block count: Sand (tons) Required: (add ½ yard to the total amount you will need) Block ...
Sand calculator online - estimate the sand required for your construction or landscaping project in weight (pounds, kilograms, tons, tonnes) and volume (cubic ft, cubic yards, cubic meters). If you are wondering 'how much sand do I need', our free sand calculator is here to do the math for you. Information about sand density, common sand types, sand grain sizes, how much a cubic yard of sand ...
Free online concrete calculator for your construction projects. Calculate the required weight and volume of readymix concrete you need for your wall, column, steps, slabs, footings, and others. Easy to use calculator for how much concrete you need in cubic feet, cubic yards, cubic meters, tons, tonnes, as well as bags of concrete of different sizes.
Sep 21, 2017· Concrete is a mix of coarse rock, fine sand and a water-activated substance that binds the rock and sand together. In the modern era, that binder is Portland cement. Ingredient Ratio. A good general purpose concrete mix combines one part Portland cement, 2.5 parts sand, three parts gravel and 0.5 parts clean water.
On-Site Concrete calculator. Use this calculator to determine how much sand, aggregate (gravel) and cement is required for mixing on site a given area of concrete (1:2:4 ratio). Please enter the dimensions in the white fields below and click calculate to display the results. See below for help on concrete.
These concrete calculators are the best way to get an idea of the amount of concrete that a project might need. You can get information in feet, inches, or yards. This is one of the most robust concrete calculators on the market. We have a concrete volume calculator, block wall calculator, and a column calculator.
To Calculate Yardage needed for your project enter the Width of Circle and Depth.. Note: you must enter your Depth Key Code Value. into the "Circular Calculator" for Correct Calculation. Example: A contractor is putting in a round pool with a 20 foot wide diameter, the base material that is needed should be 8 inches deep (see Depth Key Code).
Work with Sandee's Soil & Rock to calculate the landscape materials & concrete flatwork you need in Ogden, UT. Visit our website for our calculator.
You can use this concrete calculator to help you determine the number of bags of QUIKRETE® Concrete Mix, Mortar Mix, or Fast-Setting Concrete you will need for the following projects. ... Jointing Sand bags you will need for your project. ... Hardscapes Rocks and Sands.
Concrete Materials. 1500 N. Sweetman Place Sioux Falls, SD 57105 Ph: 605.336.5760 1500 N. Sweetman Place | Sioux Falls, SD 57105 Contact Call
This series of concrete calculators has been developed to help you plan your project. You can calculate how much concrete, cement, sand, mortar or render you will need. For each calculation you will have to know the dimensions of your object. The calculator will perform the sums for you - where relevant it will add a small percentage for the wastage that inevitably happens when mixing & using ...